This is a fully comprehensive instructional course in getting into the business of repairing all makes of laptops. Chip-level Training will be customized for your present knowledge of electronics. If you go through the fundamental track , all the power electronic components will be introduced before we move to the logics section. After you become comfortable with power electronics the logic session follows . It is an intensive coverage into the intricate details of chip-level service of the laptops. This involves detailed circuit tracing , signal analysis , replacement of SMD devices and all the tips and tricks our service engineers acquired from the years of experiences. the session makes you confident enough to chip-level service the new generation notebooks from Lenova , Compaq, HP , Toshiba ,Sony and the like .
Service Technicians entering into the Laptop training course must have experience in the following disciplines
Ready To Learn A New Skill Online?
Would love to know how you diagnose motherboards on a component level. What tools do you use?
I find it is very hard to explain this. actually, it is very simple and can be described in two words: current and singal. read the current change during booting tells you where the machine stopped. check the singals on the different part of motherboard tells what is wrong or what may missing.
Tools are: smd rework station, bga rework station, power supply has current meter. all the rest tools you can find in any radio tv repair shop.of course all the datasheets for the components, especially the schematic diagram, you will find it much difficult without it.
What are common faults on mainboards?
Do certain components fail? Is there a trend as to which parts fail quite often?
Different maker/model has different common fault. Toshiba S1 is vga chip, and can't be repaired(well, almost can't be repaired because the pcb quality is not very good so successful rate is very
HP DV2000, 6000, 9000, compaq v3000, v6000, dell 1210, all those use nvidia chips have problem on vga chip or north bridge. easy to repair but have to make fan keep spinning after repaired, otherwise will break down in 1 or 2 week again.
hp nx5000, cpu pwm chip dry joint. acer 290, cpu pwm dry joint.
hp dv1000, compaq m2000 protection circuit easy to blow up.
ibm t40 vga dry joint problem.
These are just few of them. every machine has its own common fault. but dry joint is the common problem for all machines. Motherboard repair is not as difficult as people thought, i think much easer than repair a tv.
Dell 1525 Inspiron that says system does not recognize the installed battery this system will not charge the battery.
Charging battery in Dell laptop involves two major chips: EC(or someone call it super IO), PWM chip for battery charging. BIOS has no part of charging. Battery communicate with EC through
SMB(system management bus??) and EC controls charging PWM. Fix charging problem is very hard in laptop repair, you must fully understand schematics, where all the signals come from and where to
Today's laptops are less and less with programmed EC, Dell 1525 has no programmed EC so it can be replaced with same model.
How i fix a DV6 with power problem. The problem of machine is it cannot power up at all.
Doing routine check:
1. system power: 3V, 5V all presented - ok
2. NBSWON signal: 3.3V presented - ok
3. press power button, NBSWON pull down to 0V, ok
4. check DNBSWON while press power button, no response. - problem.
in here I made a mistake, I didn't pay attention of the voltage of DNBSWON, this mistake waste me the next few days time. It should be 3.3V, but only about 1V.
Change EC as usual, because I thought the EC has problem. Then the big trouble comes - it auto power up once I plug in the power but stop in 0.04A current. Check and find no S5_ON signal, which
indicate south bridge has problem, so change south bridge. But still same problem and still no S5_ON. I find that the EC I change is kb3926A rather than kb3926C. In most case, this is no problem but
in very rare occation...
So I find a 3926C and put on. Now the motherboard is back to the same problem while I first start to check! So I change a wrong EC and this time I change a correct one, and also EC has no problem!
Because EC will start to read bios once the power plug in(not as people think, once you press power button). I check BIOS chip, BIOS_CS should have a countinue wave form but it just one stright line. BIOS chip is faulty, I replace the BIOS chip and it works perfect.
Okay, so the USB ports seem totally dead, no power at all. It is because some soda was spilled on it (I presume, at least, may be randomly related with something else). I also corrupted my OS X install, have to reinstall freshly. Now, I haven't reset the SMC or PRAM yet, and that's the first thing I'll do (however as there's is no 5V power, I doubt this will fix it, correct me if I am wrong). However, if that goes sour, and won't fix the problem, what are my options? Here's how I was thinking:
Firstly, can someone tell me all the devices I should be seeing in the system profiler under USB? Also, isn't it so that a central USB controller also handles the internal keyboard and iSight which still work perfectly, meaning that only the ports themselves are damaged? Let's presume so, and that the USB controller chip is still okay. Should I just replace (desolder old, solder new) the female USB ports, or could the problem lie in the connection between them and the USB controller, and if the latter, how would one go about fixing it?
I think you need to start with the physical USB port/s of the system.Remove the battery pack & disassemble your system. I would clean the area where the soda spilled thoroughly of any soda that might be still present. Use distilled water on cotton swabs (Q-Tips) to clean things and then use isopropyl alcohol to then treat the areas to act as a dryer and look for any damage.
If the USB outlets are damaged (corroded) you'll need to replace the full logic board as they can't be easily removed without damaging the logic board. Replacing any of the components of the logic board requires very special SMT tools and not really serviceable.
The fact AHT does not find any problems implies your circuits (USB controller) are AOK. So most likely the USB sockets have become damaged. And, Yes, your USB devices do show up under the Apple Profiler application if they are seen.You also need to take power sources away from it (battery, etc...) and clean up after the liquid damage. Yes there is only 1 USB controller. However, the USB controller has 4 channels operating 8 deices (2 per channel), without looking at the schematics I couldn't tell you if both ports are on the same channel, though I doubt it. It is possible for 1 channel to be bad on the USB controller and the rest to function properly. The USB specification is about data transfer rate and not about amperage to power or charge something. Please tell us more about the devices you have attempted to hook up to the USB port(s). On the USB ports there is, among other things, a 15K OHM resister that creates the amperage for the port (on all the Apple motherboards I have inspected). It is a 402 SMD package, less than 1mm in length, and you really need a stereo microscope to solder it in. The actual physical port you attach to is a rarely at fault without it being physically damaged to the point of not passing visual inspection.
Apple logic board has a lot of SMT components near the sockets that a heat gun will disturb. Focus on cleaning the soda spillage and then see where things are. One thing I did forget to ask is your USB device/s powered or unpowered? Your USB I/O could be OK, but, the power side of the port could be damaged. Try a powered device or hub to see if thats your problem.
A question I am often asked is "How can I tell if the backlight or inverter has failed on my laptop/monitor as I can only just make out an image?"
The answer is that there are several causes of a dim display or the failure of a backlight to illuminate the screen. As most people are aware, inverter and backlight failure are the most common. Other causes are:- a faulty or damaged LCD/Inverter cable, Faulty motherboard and a faulty screen.
Firstly try the obvious!
There is a little switch usually located near the hinge which switches the display off when the lid is closed. This can sometimes get jammed and is easily overlooked. It might simply be a question of unjammimg it or making some sort of repair to it.
Most laptops are able to toggle between an external display and the built in screen. Sometimes the laptop can get confused so it is worth toggling between external and built in screen. As most have several different settings it is worth doing this several times. If the laptop screen flashes when you do this it would indicate that the inverter is trying to start the backlight. This means that there is a good chance that either the backlight or inverter has failed but does not totally rule out the other components.
It may also be worth resetting the bios as these settings can sometimes be lost especially if the cmos battery is on its way out or has been disturbed.
Unfortunately, unless you are a qualified electronics engineer it is very difficult to test the individual boards and components and fault location is basically a case of substitution until the problem is cured or you decide not to spend anymore money on it!
Laptops usually only have 1 backlight so obviously if the backlight fails there is no illumination of the screen but the same result happens if the inverter or one of the other components mentioned above fails!
In the case of monitors, most monitors have 2 or more backlights and it would be unusual for all the backlights to fail at the same time so if you have no illumination of a monitor screen but the power light is green then chances are the inverter has failed. A failed backlight on a monitor will result in one half of the screen appearing brighter than the other half.
Backlights can be tested by connecting them to a known good inverter. You can use one of the inverters they sell for case moding. Just provide a 12V input for it and connect your backlight to one of the output sockets. If your backlight illuminates then it is OK and the fault lies elsewhere. A pink or red hue to the screen is nearly always a sign of a failing backlight and if this happens it is well worth replacing the backlight as the only other thing that can cause this is a faulty screen.
Remember backlights work on an AC Voltage of around 1000v and although the wattage is very small can give you a nasty shock and could prove fatal if you have a pacemaker or similar.
We now come to an item that can only be tested by a qualified electronics engineer or simply substituted. There is usually a small fuse located near the input connector. Check this for continuity. Depending on the inverter there can be several inputs but it is worth checking the input voltages. Basically you will have a positive and negative feed plus a switching voltage and a brightness connection. The basic voltage for powering the inverter is usually the same as you laptop input voltage but the switching voltage may be as low as 5 volts DC. The brightness voltage can be anything from 0 to 5 volts but normally full brightness is acheived with 0 volts so don't worry about this. Unfortunately inverters often have up to 20 or more connections and may incorporate circuits which show battery charge status, on/off status and almost anything else you care to name! As wiring diagrams are rarely available its impossible to know which connection does what. It is possible by a process of elimination to work out the main positive and negative terminals and you may often find there are several of these but the rest is pure guesswork. If you have an analogue multimeter, set it to the highest AC reading (usually 1000V) and check for an output from the inverter. Initial start up voltage will probably exceed 1000 volts but normal running voltage should be below 1000 volts depending on the size of your screen. Look for a voltage in the region of 400 - 900 volts. Obviously if you are getting a good voltage here then your backlight has failed. Otherwise I am afraid it is a case of replacing with a known good inverter to see if this cures the problem. (If anyone knows of a foolproof way to test an inverter please enlighten me)
Check this cable carefully for damage especially in the hinge area and make sure the connectors have not worked loose. It is possible for the wires to break internally with no obvious signs of damage so check the continuity of the cables. A faulty LCD cable can even result in your laptop not switching on.
The motherboard sends a signal to the inverter board telling it when to switch the backlight on. If there is a fault on the motherboard then the inverter board will not receive a signal and therefore not switch the backlight on. It may be possible to check the input voltages to the inverter board with a multimeter but if you have eliminated the previous items I have found this to be quite a commom fault. NB If you connect your laptop to an external monitor and get a good picture this only proves that the video card is OK, there could still be a fault on the motherboard which is preventing your screen from illuminating.
It is possible for a faulty screen electronics to result in the backlight failing to illuminate. This is rare but can happen and if you have eradicated the previous items is the only possibility left.
|Convenience: – Download all courses via the Internet. Also a copy of the course will be sent to you via email attachment. Download, print and study at your own pace|
|Learn New Innovative and Productive Techniques: Discover new ways to be productive throughout your day with these Repair tips and tricks.|
|Flexibility : Attend classes at anytime and from anywhere in the world|
|Available 24/7 Middle of the night. You need a quick answer on how to get a task done on your Laptop. Jump online and read about the fault. Problem solved.|
|Affordable :We provide high quality courses with much lower tuition than other training organizations.|
|Clear, and Comprehensive Training Our Trained Laptop Repair Specialist will help you with any questions, provide you additional resources, and keep you up-to-date with rapidly changed technologies.|
|Technical Questions ? Find Answers to Your Laptop Problems Now|
|Secret Codes: Know All The Most Important New Secret Bios Codes|
We strive to be the number one institute offering the most competitive Laptop courses which cover the entire essential areas varying from its hardware to software parts. Hence, after completing the course you will be able to fix any laptop problem.
The Course is so bleeding edge? putting a price tag on this course wasn?t easy.
The average tuition for just a basic newbie personal computer 101 course at your local college is $1685. And, this course is so advanced, there aren’t even any other courses available for it yet! So you couldn’t enroll for $1685 even if you wanted to.
I know you already invested a lot of your hard-earned money on buying your laptop. And, today’s economic times are tough. So, I’m not going to charge you anywhere near $1685. This course will be
less than one-tenth of the cost of the most basic college computer course at
$197. (UPDATE: See Limited Time Offer Below…)
I meant it when I said this is the best opportunity for you to get the absolute most out of your laptop? so I'm going to make this a complete no brainer for anyone to get involved and take action right away.
So, for a limited time you can get your hands on the entire course for a one-time payment of just
After purchasing, you’ll have immediate access.
And, for a onetime payment, you’ll get lifetime access, so any future updates or changes will be yours for FREE.
1. Laptop motherboard Repair (Chip Level) How to check dead board
2. How to check Memory DDR1 Fault Laptop Repair (Chip Level)
3. How to Check Dead Desktop Motherboard(step by step)
4. How to fix a broken hard drive. Beeping And clicking noise
5. Testing the charging circuit on a laptop motherboard
6. How to Solder QFN MLF chips Using Hot Air without Solder Paste and Stencils
7. Reballing With Low Cost/HomeMade Equipement
8. How to test a laptop motherboard outside of the machine
9. Advanced troubleshooting technique tutorial of how to possibly fix a PC that will not beep at boot
10. Identifying bad capacitors on motherboards and adapter cards
PLUS LIFETIME UPDATES!!!!
We sell the following products with full 1 year warranty and technical support.
This is the Hp Dv 6000 with blank screen display
White vertical lines on the screen
This is the Nvidia gpu chip on the motherboard
You must sprade flux around the eage of the chip
Now position on the reball machine for chip removal
The chip has be removed from the motherboard
Clean and add the new balls to the chip
Send the chip back to the reball machine for re-soldering
Allow the motherboard to cool down before turning it on
Operation Completed Successfully